part a drain 2.8.1 : earth work in excavation by mechanical means (hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.all kinds of soil 5.9.1 : centering and shuttering including strutting, etc. and removal of form for:foundations, footings, bases of columns, etc for mass concrete 4.1.6 : providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) 5.1.2 : providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size 5.22.6 : steel reinforcement for r.c.c work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelthermo - mechanically treated bars of grade fe-500d or more 13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) od40740/20222023 : removing and relaying interlocking tiles including all cost of labour and materials etc. complete as directed by the officers of matsyafed. od40785/20222023 : providing and laying of interlocking concrete block pavements having thickness 80 mm as per drawings and technical specification. 51.2.3 : filling with quarry muck
filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the cbr value of subgrade part b kitchen 2.8.1 : earth work in excavation by mechanical means (hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.all kinds of soil 50.6.1.1 : solid block masonry using pre cast solid blocks ( factory made) of size 40x20x20cm or nearest available size confirming to is 2185 part 1 of 1979 for foundation and plinth with thickness 20 cm and above in: cm 1:6 ( 1 cement : 6 coarse sand) etc complete 50.6.3.2 : solid block masonry using pre cast solid blocks (factory made) of size 40x20x10 cm or nearest available size confirming to is 2185 part i of 1979 for super structure up to floor two level for 10 cm thick wall in : cm 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete 50.18.9.8.2 : providing and fixing pvc pipes includings of pipes with one step pvc solvent cement, trenching and refilling & testing of joints complete as per direction of engineer in charge. 75 mm dia 4 kgf/cm2 50.18.9.9.1 : providing and fixing pvc pipes includings jointing of pipes with one step pvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.110 mm dia 6kgf/cm2 4.1.8 : providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) 2.25 : filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. 13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 12.1.3 : providing corrugate g.s. sheet roofing including vertical/ curved surface fixed with polymer coated j or l hooks, bolts and nuts 8 mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gm/m2 od43066/20222023 : providing false ceiling using 6mm cement board including all cost of materials and labour etc complete as directed by the officers of matsyafed. 50.10.2 : steel work for purlin/single section with g i pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete 12.4.2 : providing ridges or hips width 60 cm overall width plain g.s. sheet fixed with polymer coated j or l hooks, bolts and nuts 8 mm dia g.i. limpet and bitumen washers complete.0.63 mm thick with zinc coating not less than 275 gm/m2 od43096/20222023 : supplying and fixing 200 mm upvc gutter in the side of roof afte fixing 25 x 8 mm iron flat clamps in trusses including all materials and labour etc. complete . as directed by the officers of matsyafed. 17.9.1 : providing and fixing kitchen sink with c. i brackets, c.p. brass chain with rubber plug, 40 mm c.p brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required:white glazed fire clay kitchen sink of size 600x450x250 mm 21.1.1.2 : providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is : 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminnium snap beading for glazing /paneling, c.p. brass/ stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge.(glazing, paneling and dash fasteners to be paid for separately):for fixed portionpowder coated aluminium (minimum thickness of powder coating 50 micron) 11.49.2 : providing and laying vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08 and conforming to is : 15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to is : 15477, in average 6 mm thickness, including grouting of joints (payment for grouting of joints to be made separately).size of tiles 600x600 mm od41520/20222023 : providing and fixing i st quality ceramic glazed wall tiles conforming to is : 15622<br>(thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy,<br>bottle green, black of any size as approved by engineer -in-charge, in skirting, risers of steps and dados,<br>over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry<br>@ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 13.82.2 : wall painting with acrylic emulsion paint, having voc (volatile organic compound) content less than 50 grams/ litre, of approved brand and manufacture including applying additional coats wherever required, to achieve even shade and colour.two coats od43102/20222023 : construction of soak pit using precast ring 1.2m dia and 1.8m depth including all cost of materials and labour etc. complete as directed by the officers of matsyafed. part c aquarium building 13.47.1 : finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade:new work (two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) 13.61.1 : painting with synthetic enamel paint of approved brand and manufacture to give an even shade:two or more coats on new work 50.9.1.1 : providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality anjili wood /jack wood 9.71.1 : providing and fixing is : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:125x64x2.50 mm 9.71.3 : providing and fixing is : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:75x50x2.50 mm 9.97.2 : providing and fixing aluminium tower bolts, isi marked, anodised(anodic coating not less than grade ac 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:250x10 mm 9.142.2 : 35 mm thick factory made solid panel pvc door shutter, made out of single piece extruded solid pvc ( 0.2 mm) thick, having styles & rails (except lock rail ) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinges side of the profile for better screw holding power, including reinforcing with ms tube of size 40 mm x 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of pvc solvent cement, self driven self tapping screws & m.s. rectangular pipes bracket of size 190 mm x 100 mm of cross section size 35 mm x 17 mm s 1 mm at each corner. single piece extruded 5 mm thick solid pvc lock rail of size 115 mm x 35 mm x 35 mm, out of which 95 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm single piece solid pvc extruded sheet inserted in the door as panel, all complete as per manufacturers specification and direction of engineer-in-charge.decorative finish (wood grained finish) 18.48 : providing and placing on terrace (at all floor levels) polyethylene water storage tank :isi 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 17.7.1 : providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:white vitreous china wash basin size 630x450 mm with a pair of 15 mm c.p. brass pillar taps 17.18.1 : providing and fixing p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is: 7231, with all fittings and fixtures complete.10 litre capacity - white 18.51.1 : providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms.15 mm nominal bore 19.18.1 : supplying and fixing c.i with out frame for manholes:455 x 610 mm rectangular c.i cover ( light duty ) the weight of the cover to be no less than 23 kg 50.18.7.3.2 : providing and fixing pvc pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step pvc solvent cement and testing of joints complete as per direction of engineer-in-charge 25 mm dia 10kgf/ cm2- internal work- exposed on wall 50.18.7.4.1 : providing and fixing pvc pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step pvc solvent cement and testing of joints complete as per direction of engineer-in-charge 32 mm dia 10kgf/cm2- internal work - exposed on wall od42538/20222023 : supplying and fixing 3 mm thick aluminium composite pannel of approved make and colour in the existing aluminium frame work. screwing the pannel and covering the joints with silicon paste etc.complete including all cost of materials and labour complete as directed by the officers of matsyafed. 10.2 : structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 25.1 : providing and supplying aluminium extruded tubular and other aluminium sections
as per the architectural drawings and approved shop drawings , the aluminium
quality as per grade 6063 t5 or t6 as per bs 1474,including super durable powder
coating of 60-80 microns conforming to aama 2604 of required colour and shade
as approved by the engineer-in-charge. ( the item includes cost of material such
as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium
frame work. nothing extra shall be paid on this account). 11.41.2 : providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08 and conforming to is : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.size of tile 600 x 600 mm. 4.1.8 : providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) electrical work 1.10.2 : wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm frls pvc
insulated copper conductor single core cable in surface / recessed medium class pvc conduit,
with modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls
pvc insulated copper conductor single core cable etc as required.group b 1.55.2 : wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm frls pvc insulated copper conductor single core cable in surface/ recessed pvc conduit, and earthing the point with 1.5 sq. mm frls pvc insulated copper conductor single core cable etc. as required.group b 1.14.1 : wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface / recessed medium class pvc conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire 1.14.2 : wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface / recessed medium class pvc conduit as required2x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire 1.14.3 : wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface / recessed medium class pvc conduit as required2 x 4 sq. mm + 1 x 4 sq. mm earth wire 1.14.5 : wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface / recessed medium class pvc conduit as required2 x 10 sq. mm + 1 x 6 sq. mm earth wire 1.14.4 : wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface / recessed medium class pvc conduit as required2 x 6 sq.mm + 1 x 6 sq.mm earth wire 90.12.7.40 : supply, laying and clamping of 1 no. pvc insulated and pvc sheathed armoured aluminium power cable, 1.1 kv grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 1.17.3 : supplying and drawing following sizes of frls pvc insulated copper conductor, single core cable in the existing surface / recessed steel/ pvc conduit as required.3 x 1.5 sq.mm 1.17.12 : supplying and drawing following sizes of frls pvc insulated copper conductor, single core cable in the existing surface / recessed steel/ pvc conduit as required.3 x 2.5 sq. mm 9.1.32 : supplying and making end termination with brass compression gland and aluminium lugs for
following size of pvc insulated and pvc sheathed / xlpe aluminium conductor cable of 1.1 kv
grade as required.4 x 10 sq. mm (25mm) 1.21.1 : supplying and fixing of following sizes of medium class pvc conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm 1.21.2 : supplying and fixing of following sizes of medium class pvc conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm 90.6.5.13 : supply and drawing the following sizes of multi-core pvc insulated & frls pvc sheathed 650/1100 v grade copper conductor round flexible cables conforming to is 694 part i 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes. 90.11.1.15 : supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of mcb db including copper /brass bus bar, neutral link, earth bus and din rail suitable for fixing mcb/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required 2.3.3 : supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (but without mcbirccb/isolator12 way, double door 2.10.1 : supplying and fixing 5 amps to 32 amps rating, 240/415 volts, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required.single pole 2.15.3 : supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (rccb), having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required.63 amps 2.13.2 : supplying and fixing following rating, four pole, 415 volts, isolator in the existing mcb db complete with connections, testing and commissioning etc. as required.63 amps 2.14.2 : supplying and fixing following rating, double pole, (single phase and neutral), 240 v, residual current circuit breaker (rccb), having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required.40 amps 1.24.1 : supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch 1.24.4 : supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet 1.27.1 : supplying and fixing following size/ modules, gi box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 module (75mmx75mm) 1.27.2 : supplying and fixing following size/ modules, gi box alongwith modular base & cover plate for modular switches in recess etc as required.3 module (100mmx75mm) 1.31 : supplying and fixing suitable size gi box with modular plate and cover in front on surface or in
recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps
modular switch, connection etc. as required. (for light plugs to be used in non residential
buildings). od44280/20222023 : supplying and fixing suitable size gi box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. od44910/20222023 : supply and fixing 305 mm sweep heavy duty exhaust fan in metal frame including all cost materials mas directed by the officers of matsyafed 90.4.9 : charges for cutting holes suitable for accommodating exhaust fans above 305mm sweep and up to 450mm sweep including plastering colour washing etc. as required. od44300/20222023 : supply and installation of 400mm sweep wall fan including all cost materials for fixing as directed by the officers of matsyafed (make: almonard/orient/havells/equivalent) od44319/20222023 : supply and fixing of 20-24 w led tube light fitting,including connection with 1.5 sq.mm frls pvc insulated copper conductor,single core cable and earthing etc.as required complete with all necessary accessories including all cost of labour and materials od44320/20222023 : supply and fixing of angle batten holder with 9w led bulb as required od44874/20222023 : supply and fixing of 15w led bulb with bulk head light fitting oval as required connections etc od44860/20222023 : supply and fixing of 40w 4000 lumen led, ip 66 street light fitting with aluminium housing including connection with 1.5 sq.mm frls pvc insulated copper conductor single core cable and earthing etc. as required complete with all necessary accessories including od pipe for mounting the light with all cost of labour and materials. od44861/20222023 : supply and fixing of 25 w led street light fitting,including connection with 1.5 sq.mm frls pvc insulated copper conductor,single core cable and earthing etc.as required complete with all necessary accessories including od pipe for mounting the light with all cost of labour and materials od44862/20222023 : earthing with g.i. earth pipe 2.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required 90.16.1.2 : supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required 90.16.1.3 : supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required od44877/20222023 : fabrication, supply & installation of dust and vermin proof, wall/ floor mounting, metering cubicle of cubicle construction made from 1.60 mm crca sheet, providing necessary supports made from the same gauge crca sheet to fix kseb meters, tpn switch, fuse unit etc, hinged door construction for the front side with compartments if necessary, providing vision panel for the meter compartment, knock out for cable entry and exit, painting the entire board with 2 coats of synthetic enamel paint over a coat of zinc chromate primer etc as required including fixing it on wall, making good the damages colour washing<br>etc. as required. crca sheet alone be used for the fabrication. angles/ flats/ slotted angles etc shall not be used for the fabrication of main housing of meter board.( including 3nos 63a hrc fuse base with hrc link,63a base neutral link and 3 phase meter board as required for the building as directed by the<br>officers of matsyafed
