part a civil work 12.8 : providing non- asbestos high impact polypropylene reinforced cement 6 mm thick corrugated sheets (as per is: 14871) roofing up to any pitch and fixing with polymer coated j or l hooks, bolts and nuts, 8 mm dia g.i. plain and bitumen washers or with self drilling fastener and epdm washers etc. complete (excluding the cost of purlins, rafter and trusses), including cutting sheets to size and shape wherever required. 12.13.1 : providing and fixing non- asbestos fibre cement high impact polypropylene reinforced roofing accessories in all colours with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers or with self drilling fastener and epdm washer etc. complete:corrugated apron pieces 15.7.4 : demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge.in cement mortar 21.1.1.2 : providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is : 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminnium snap beading for glazing /paneling, c.p. brass/ stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge.(glazing, paneling and dash fasteners to be paid for separately):for fixed portionpowder coated aluminium (minimum thickness of powder coating 50 micron) 21.3.1 : providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer - in -charge. ( cost of aluminium snap beading shall be paid in basic item):with float glass panes of 4.0 mm thickness 21.3.2 : providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer - in -charge. ( cost of aluminium snap beading shall be paid in basic item):with float glass panes of 5.50 mm thickness 21.12.3 : providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0mm thick & 2100 mm long with s.s. screws etc. complete as per direction of engineer -in-charge.polyester powder coated minimum thickness 50 micron aluminium tubular handle bar 21.13 : providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete 50.6.1.7 : solid block masonry using pre cast solid blocks ( factory made) of size 40x20x15cm or nearest available size confirming to is 2185 part i of 1979 for foundation and plinth with thickness 15 cm in : cm 1:6 ( 1 cement : 6 coarse sand ) etc complete 50.6.1.8 : solid block masonry using pre cast solid blocks (factory made) of size 40x20x15cm or nearest available size confirming to is 2185 part i of 1979 for super structure up to floor two level with thickness 15cm in: cm 1:6 ( 1 cement : 6 coarse sand etc complete 50.9.1.1 : providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality anjili wood /jack wood 50.9.3.1 : providing and fixing paneled or paneled and glazed shutters for doors, windows and clerestory windows, 30 mm thick shutters including isi marked m.s. pressed butt hinges bright finished of required size with necessary screws, excluding paneling which will be paid for separately, all complete as per direction 0f engineer in- charge.
using anjili/ jack wood 13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 11.39 : providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to is: 15622, of approved make in colours white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. 11.41.2 : providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08 and conforming to is : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.size of tile 600 x 600 mm. 17.3.2 : providing and fixing white vitreous china pedestal type water closet (european type) with seat and lid, 10 litre low level white vitreous china flushing cistern & c.p. flush bend with fittings & c.i. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :w.c. pan with isi marked black solid plastic seat and lid 17.10.1.2 : providing and fixing stainless steel a isi 304 (18/8) kitchen sink as per is 13983 with c.i. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:kitchen sink with drain board510x 1040 mm bowl depth 225 mm 17.60.2.2 : providing and fixing trap of self cleansing design with screwed down or hinged grating without vent arm complete, including cost of cutting and making good the walls and floors:100 mm inlet and 75 mm outletsand cast iron s & s as per is - 1729 18.17.2 : providing and fixing gun metal gate valve with c.i. wheel of approved quality (screwed end) :32 mm nominal bore 50.17.1.1 : supplying and fixing stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site engineer-in-charge. 50.17.1.4 : supplying and fixing cp health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge. 50.18.8.9.1 : providing and fixing pvc pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes with one step pvc solvent cement and testing of joints complete as per direction of engineer-in-charge. concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2 50.18.9.3.2 : providing and fixing pvc pipes includes jointing of pipes with one step pvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge. 25 mm dia 10kgf/cm2 50.18.9.6.2 : providing and fixing pvc pipes includings jointing of pipes with one step pvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge. 50 mm dia 6 kgf/cm2 51.19.st1 : supplying and installing ready made pvc septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (provision for cc/rcc/sand/06mm aggregate for the preparation of bed shall be paid separately)
1. below 15 flush capacity 9.117.2 : providing and fixing factory made upvc door frame made of upvc extruded sections having an overall dimension as below (tolerance 1 mm), with wall thickness 2.0mm (0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. the hinge side vertical of the frames reinforced by galvanized m.s. tube of size 19 x 19 mm and 1 mm ( 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of engineer-in-chargeextruded section profile size 42x50 mm 9.118.1 : providing and fixing to existing door frames24 mm thick factory made pvc door shutters made of styles and rails of a upvc hollow section of size 59x24 mm and wall thickness 2 mm ( 0.2 mm) with inbuilt edging on both sides. the styles and rails mitred and joint at the corners by means of m.s. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. the styles of the shutter reinforced by inserting galvanised m.s. tube of size 20x20 mm and 1 mm ( 0.1 mm) wall thickness. the lock rail made up of h section, a upvc hollow section of size 100x24 mm and 2 mm ( 0.2 mm) wall thickness,fixed to the shutter styles by means of plastic/galvanised m.s. u cleats. the shutter frame filled with a upvc multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ( 0.1 mm) wall thickness. the panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised m.s. rod and fastened with nuts and washers, complete as per manufacturers specification and direction of engineer-in-charge( for w.c. and bathroom door shutter). od247053/20212022 : construction of soak pit using pre cast ring 1.2 m dia and 1.8 m depth including all<br>cost of materials and labour etc. complete as directed by the officers of matsyafed. 10.6.3 : supplying and fixing rolling shutters of approved make, made of required size m.s. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to is: 4454 - part 1 and m.s. top cover of required thickness for rolling shutters.80x0.90 mm m.s. laths with 0.90 mm thick to cover 13.47.1 : finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade:new work (two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) 13.61.1 : painting with synthetic enamel paint of approved brand and manufacture to give an even shade:two or more coats on new work od256303/20212022 : supplying and fixing gi frame work for false ceiling using 1'' 'c' channel as perimeter 2'' 'c' channel as inner section and 2.5'' ceiling section including all cost of material and labour, as directed by the officer of matsyafed. od256378/20212022 : providing and fixing false ceiling with 90 mm thicktkt panel board ceiling of approved quality in aluminium frame work with necessary screws etc complete (aluminium frame work shall be paid seperately)
