Active tenders in Bend

fabrication, transportation, and installation of 05 no. h.t. pumps complete set along with 6.6. kv electricals, valves, bends, pipes from surface to u.g. rvi seam through muv at mic, jpc. .

ttps operation circle mpm ii unit v replacement of pulverized coal pipes, bends and fittings by new ones/reconditioned ones between boiler inlet elbow and sleeve coupling at 10.5mtr to 32 mtr level of boiler area during 2021 annual overhaul

ttps operation circle mpm ii unit v replacement of pulverized coal pipes, bends and fittings by new ones reconditioned ones between mill and upto sleeve couplings during 2021 annual overhaul

auction of lot number-6

supply of 1 m.s.rubber lined pipe 2 m.s.bend

m04215-procurement of boiler tube bends for boiler pp st-1 ntpc mauda

dismantling, fabrication, transporting and fitting of one no.240 mtr. head 500 gpm pump with 175kw motor with all valves and bends and pipe from surface to 26d/+1l through muv at mic , jpc. .

supply of 1 pvc conduit 25 mm 2 pvc junction box, 3 way, 25mm 3 pvc junction box (four way) size 1 4 pvc bend 25mm dia ( for conduit) 5 pvc insulated multistrand copper conductor single core cable of size 2.5 sq.mm 6 steel screw 1-1/2 ( in kg) 7 conduit clamp 25 mm 8 mcb distribution box 12 way spn 9 single pole mcb 6 amp 10 2 p mcb 240 v ac 10 a 11 rccb, dp, 16a, 230v, sensitivity - 30 ma 12 pvc insulation tape

fabrication, transporting and fitting of one no.300 mtr. head pump with 160 kw motor with starter and all valves and bends from surface to 28l/34d through muv then to 28l, 32d manually at mic, jpc. .

fabrication, transporting and fitting of one no.300 mtr. head pump with 160 kw motor with starter and all valves and bends from surface to 28l/34d through muv then to 28l, 32d manually at mic, jpc. .

replacement of vertical pump ( 361-t) delivery pipe, bends , its base frame, flange and drain nipple and supporting structure after removal of damaged portion of thickener no.1 in fine coal section of kathara washery

tender for 1hp/13 stages energy efficient vertical sm pump set of 4 inch dia , water filled containing non-return valve of head -78 mtrs, lpm-23,rpm-2850,discharge size-32 mm, rust resistant aisi 410 grade stainlesssteel , anti-friction bearing, copper wound stator & rotor, to operate on single phase ac ,50 hz supply (160v-240v) range with suitable digital control panel of same make, hdpe pipe 40mm dia 50 mtrs of (pe-80,pn10kg/cm2.) attached with 32mm stainless steel nipples at both ends , 3 core 2.5 sq.mm flat submersible cable -60mtrs. including suitable clamps,bore cover, 02 nos of 32 mm ss couplings ,nipples ,flanges 50 mm,reducerbushes 11/4 to 11/2, bends nuts & bolts complete with 02 years warranty. makes: kirloskar, cri,ksb,crompton, texmo only.

supply of bends for mill reject system

tender for bend plate rh front & lh to clw drg.no. 05/3/21/4 alt-2 ref.-3.

procurement of gi pipe bends for bhualpalli area .

providing and laying of 25mm dia /38 mm dia conduits to be laid in slabs, for sub mains and for downs conduits which is to be recessed in walls including cost of ms deep junctions boxes surface boxes ,pvc bends etc. for the internal electrificati

providing and laying of 25mm dia /38 mm dia conduits to be laid in slabs, for sub mains and for downs conduits which is to be recessed in walls including cost of ms deep junctions boxes surface boxes ,pvc bends etc. for the internal electrificati

repair, replacement of pf pipes, bends, gates, dampers and gaskets etc.of bowl mill and rc feeders of unit-1 to 10

supply of angle equal ms 75 x 75 x 8 mm, standard length of 5 to 6 mtrs. or nearest, without any twist, bend etc., make: sail/vizag/tata/jindal/essar 2 angle equal ms 75x75x6 mm, standard length of 5 to 6 mtrs. or nearest, without any twist, bend etc., make: sail /vizag/ tata / jindal / essar 3 angle equal ms 65 x 65 x 8 mm, standard length of 5 to 6 mtrs. or nearest, without any twist, bend etc., as per is specification, make: sail / vizag/ tata /jindal / essar 4 angle equal ms 50 x 50 x 6 mm, standard length of 5 to 6 mtrs. or nearest, without any twist, bend etc., as per is specification make: sail / vizag/ tata /jindal / essar 5 channel ms ismc 250 , standard lengths of 5 to 6 meters without any bend, twist, rust etc. and material conforming to is specification. make: sail/vizag/tata /jindal / essar 6 channel ms 150 x 75 mm, standard length of 5-6 m, without any bend, twist etc (approved make: sail/vizag/

fabrication, shifting and erection of sieve bends feed box liner plate fitting of sieve bends, cyclone and its supporting structure after dismantling of old and damaged sieve bend, feed box, cyclone and connection of under flow/ overflow pipe etc. c