dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead - of area 3 sqm and below demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead - for thickness of tiles 10mm to 25mm demolishing lime concrete manually / by mechanical means and disposal of material within 50 metres dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scrarches etc.complete 20mm cement plaster of mix -1:4 (1 cement: 4 fine sand) painting top of roofs with bitumen of approved quality @ 17kg per 10 sq.m impregnated with a coat of coarse sand at 60cudm per 10 sq.m including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete - with residual type petroleum bitumen of grade vg-10 lime concrete terracing on roofs of required thickness laid to fall with 25mm nominal size brick aggregate and 50 lime mortar 1:2 (1 lime putty : 2 surkhi) rammed and finished with gur and belgiri treatment complete including rounding of junctions with parapet wall complete providing and laying pressed clay tiles (as per approved pattern 18mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2 integral water proofing compound , laid over a bed of 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -vengai wood providing and fixing isi marked flush door shutters conforming to is : 2202 (part 1) non - decorative type, core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters - 25 mm thick (for cupboard) including isi marked nickel plated bright finished m.s.piano hinges with necessary screws providing and fixing factory made upvc white colour sliding glazed window upto 1.50m in height dimension comprising of upvc multi - chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 + or - 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to upvc profile), appropriate dimension of upvc extruded glazing beads and upvc extruded interlocks, epdm gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), g.i. fastners 100 x8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. profile of frame & sash shyall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc.after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing.(single / double glass panes, wire mesh and silicon sealent shall be paid separately) - two track two panels sliding window made of (bigl series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 + or - 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(area of window upto 1.75 sqm upto 2.50 sqm) - sliding window size 1.50x1.35 m steel work welded in built up sections / framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets,gates and similar works providing and fixing aluminium sliding door bolts , isi marked , anodised ( anodic coating not less than grade ac 10 as per is: 1868), transparent or dyed to required colour or shade , with nuts and screws etc complete - 300 x 16 mm providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is :1868), transparent or dyed to required colour or shade, with necessary screws etc. complete - 250 x10 mm providing and fixing aluminium handles, isi marked , anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 125 mm providing and fixing facory made door frame (single rebate ) made out of single piece extruded solid pvc foam profile with homogenous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & jointed with self driven self tapping screws of size 38 mm x 4 mm & pvc solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturers specification providing and fixing factory made 30 mm thick door shutter made of solid pvc foam profile . the styles & rails shall be of size 75 mm x 30 mm having wall thickness 5mm . the styles, top & bottom rails shall have one side wall thickness of 15 mm integarally extruded on the hinge side of the profile for better screw holding power. the styles and rails shall be reinforced with m.s. tubes of size 33 mm x 17 mm x 1mm, painted with primer, all four corners of reinforcement to be welded or sealed. solid pvc extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to recive single piece extruted 5 mm pvc sheet as panel. the styles and rails will be mitred cut and joint with the help of pvc solvent cement & self driven self tapping screws. single piece extruded solid pvc lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of pvc solvent cement and self driven self tapping screws of size 100 mm x 8 mm complete as per manufacturers specifications - non decorative finish providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to is : 15622, of approved make (nitco / kajaria) in colours such as white, ivory, grey, fume red brown ,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including pointing the joints with white cement and matching pigment etc., complete providing and fixing commercial quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make (jhonson /asian / somany / nitco) in all colours, shades of size 300 x 450 mm as approved in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 300x450 mm providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) providing and laying fully vitrified floor tiles of size 600 x600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08 and conforming to is : 15622 of approved make (nitco / rak / johnson /asian ) in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete - size of tile 600 x600 mm earth work in excavation by mechanical means (hydraulic excavation) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10sqm on plan) including getting out and disposal of excavated earth, lead upto 50m and lift upto 1.5m - all kinds of soil supplying and filling in plinth with river sand under floors, including watering, ramming consolidating and dressing complete providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) brick work with common burnt clay f.p.s. (non modular ) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 coarse sand) brick work with common burnt clay f.p.s (non modular ) bricks of class designation 3.5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:6 ( 1 cement : 6 coarse sand) 15mm cement plaster on the rough side of single or half brick wall of mix - 1:4 (1cement : 4 fine sand) providing and laying 22 mm thick factory made pre-polished cement concrete flooring tiles of required colour and design over 20 mm thick cement mortar 1:4 (1 cement : 4 sand ) and jointed with cement slurry mixed with an admixture of pigment to match the shade of the tile - (endura ultra dazzle technic) demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - in cement mortar finishing walls with premium acrylic smooth exterior paint with silicon additives of required shade - old work (two or more coats applied @ 1.43 ltr / 10 sqm) over existing cement paint surface finishing walls with acrylic smooth exterior paint of required shade - new work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - two or more coats on new work supplying and filling with gravel (excluding rock) in trenches, plinth, sides of foundations etc . in layers not exceeding 20 cm in depth consolidating each deposited layers by ramming and watering etc .complete including all lead and lift providing, hoisting and fixing upto floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but excluding cost of reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) steel reinforcement for r.c.c.work including straightening, cutting, bending, placing in position and binding all complete upto plinth level - thermo -mechanically treated bars (isi brand of approved make) fe - 415 or more providing and fixing white vitreous china water closet squatting pan (indian type) - orissa pattern w.c.pan of size 580x440mm providing and fixing white vitreous china pedestal type water closet (european type) with seat and lid,10 litre low level white vitreous china flushing cistern & c.p.flush bend with fittings & c.i. brackets, 40 mm flush bend , overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required - w.c.pan with isi marked white solid plastic seat and lid providing and fixing on wall / column face unplasticed - pvc soil and waste pipes (type - b) conforming to is : 13592- 1992 including jointing with seal ring conformation to is : 5382 leaving 10mm gap for thermal expansion - single socked pipes -110mm diametre providing and fixing on wall face / column face unplasticised - pvc mould fittings / accessories for unplasticisd - pvc soil and waste pipes conforming to is : 14735 - 1999 including jointing with seal ring conforming to is : 5382 leaving 10mm gap for thermal expansion - bend 110 mm providing and fixing on wall face / column face unplasticised - pvc moulded fittings / accessories for unplasticisd - pvc soil and waste pipes conforming to is:14735 - 1999 including jointing with seal ring conforming to is :5382 leaving 10mm gap for thermal expansion - single tee without door - 110 x110x110mm providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings. this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete - external work - 20mm nominal outer dia pipes providing and fixing astm pipes including all astm plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . this includes jointing of pipes & fitting with one step astm solvent cement and testing of joints complete (internal work exposed on wall ) - 25mm nominal outer dia pipes providing and fixing astm pipes including all astm plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . this includes jointing of pipes & fitting with one step astm solvent cement and testing of joints complete (internal work exposed on wall ) - 20mm nominal outer dia pipes providing and fixing c.p.brass bib cock of approved quality conforming to is: 8931 - 15 mm nominal bore providing and fixing ball valve (brass) of approved quality, high or low pressure, with plastic floats complete - 20mm nominal bore providing and fixing gun metal gate valve with c.i.wheel of approved quality (screwed end) - 25mm nominal bore providing and fixing gun metal gate valve with c.i.wheel of approved quality (screwed end) - 20 mm nominal bore providing and placing on terrace (at all floor levels) polyethylene water storage tank isi: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank - circular tank providing and fixing wash basin with c.i. brackets, 15mm c.p. brass pillar taps, 32mm c.p.brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever required - white vitreous china flat back wash basin size 550x400 mm with single 15mm c.p. brass pillar tap providing and fixing c.p.brass angle valve for basin mixer and geyser points of approved quality conforming to is: 8931- 15 mm nominal bore supplying fixing and commisioning of suguna/ texmo / sharp 0.5 hp monoblock pumpset slow speed single phase motor. the rate include the cost of pumpset, pumpset fixing in position and test run etc.complete providing and fixing p.v.c. waste pipe for sink or wash basin including pvc waste fittings complete - semi rigid pipe - 32mm dia providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is:733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p.brass / stainless steel screws, all complete as per architectural drawings (glazing, paneling and dash fasteners to be paid for separately) - for fixed portion - anodised aluminium (anodised transparent or dyed to required shade according to is:1868, minimum anodic coating of grade ac 15) providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is:733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling , c.p.brass / stainless steel screws , all complete as per architectural drawings (glazing, paneling and dash fasteners to be paid for separately) - for fixed portion - powder coated aluminium (minimum thickness of powder coating 50 micron) providing and fixing anodised aluminium sections of ac grade 15 for fixing the grills for the doors / windows / ventilators etc., with necessary cp brass screws providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to is:12823 grade i type ii, in panelling fixed in aluminum doors, windows shutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings- pre - laminated particle board with decorative lamination on both sides providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings ( cost of aluminium snap beading shall be paid in basic item) - with float glass panes of5.50 mm thickness filling the gap in between aluminium frame & adjacent rcc / brick / stone work by providing weather silicon sealent over backer rod of approved quality as per architectural drawings complete - upto 5 mm depth and 5 mm width providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with isi, is :3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ), with necessary accessories and screws etc complete providing and fixing isi marked aluminium butt hinges anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete - 100 x 63 x 3.2 mm providing and fixing bright finished brass 100 mm mortice latch and lock, isi marked, with six levers and a pair of anodised (anodic coating not less than grade ac 10 as per is : 1868 ) aluminium lever handles of approved quality with necessary screws etc complete providing and fixing stainless steel (grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding. buffing, polishing and making curvature (whereever required) and fitting the same with necessary stainless steel nuts and bolts complte. i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab withsuitable arrangement (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.,)
