earth work in excavation by mechanical means (hydraulic excavation) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10sqm on plan) including getting out and disposal of excavated earth, lead upto 50m and lift upto 1.5m - all kinds of soil filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finsishing and reinforcement all work upto plinth level 1:1.5:3 (1cement: 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and sting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centering , shuttering, finishing and reinforcement - 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) centering and shuttering including strutting, propping etc and removal of form for - foundations, footings, bases of columns etc for mass concrete centering and shuttering including strutting, propping etc and removal of form for - suspended floors, roofs, landings, balconies and access platform centering and shuttering including strutting, propping etc and removal of form for - columns, pillars, piers, abutments, posts and struts steel reinforcement for r.c.c.work including straightening, cutting, bending, placing in position and binding all complete upto plinth level - thermo -mechanically treated bars (tiscon / vizag/ iisco / sail / jsw) fe - 415 or more brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in - cement mortar 1:4 (1 cement : 4 coarse sand) half brick masonry with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundations and plinth in - cement mortar 1:4 (1 cement :4 coarse sand) providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -padak wood providing and fixing panelled or panelled and glazed shutters for doors, windows, and clerestory windows, including isi marked m.s.pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately , all complete - padak wood - 35 mm thick shutters providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick - padak wood providing 40 x 5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30 x10 x 15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) providing and fixing isi marked aluminium butt hinges anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete - 125 x 75 x 4 mm providing and fixing isi marked aluminium butt hinges anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete - 125 x 63 x 4 mm providing and fixing aluminium sliding door bolts , isi marked , anodised ( anodic coating not less than grade ac 10 as per is: 1868), transparent or dyed to required colour or shade , with nuts and screws etc complete - 300 x 16 mm providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is :1868), transparent or dyed to required colour or shade, with necessary screws etc. complete - 300 x10 mm providing and fixing aluminium handles, isi marked , anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 125 mm providing and fixing aluminium hanging floor door stopper , isi marked , anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour and shade with necessary screws etc complete - twin rubber stopper providing and fixing bright finished brass 100 mm mortice latch and lock, isi marked, with six levers and a pair of anodised (anodic coating not less than grade ac 10 as per is : 1868 ) aluminium lever handles of approved quality with necessary screws etc complete providing and fixing factory made upvc door frame made of upvc extruded sections having an overall dimension as below (tolerance + 1mm ), with wall thickness 2.0 mm (+-0.2mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws , joints mitred and plastic welded. the hinge side vertical of the frames reinforced by galvanized m.s.tube of size 19 x 19 mm and 1mm (+-0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturers specification - extruded section profile size 48 x 40 mm providing and fixing to existing door frames - 30 mm thick factory made polyvinyl chloride (pvc) door shutters made of styles and rails of a upvc hollow section of size 60 x 30 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt decorative moulding edging on one side . the styles and rails mitred and joint at the corners by means of m.s. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws . the styles of the shutter reinforced by inserting galvanised m.s.tube of size 25x20 mm and 1mm (+- 0.1mm) wall thickness . the lock rail made up of h section , a upvc hollow section of size 100 x 30 mm and 2 mm (+-0.2 mm) wall thickness , fixed to the shutter styles by means of plastic / galvanised m.s. u cleats. the shutter frame filled with a upvc multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+ 0.1mm) wall thickness . they panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised m.s.rod and fastened with nuts and washers, complete as per manufacturers specification providing and fixing of 65 mm godrej navatal lock of 7 levers with 3 keys etc complete providing and fixing factory made upvc white colour sliding glazed window upto 1.50m in height dimension comprising of upvc multi - chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 + or - 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to upvc profile), appropriate dimension of upvc extruded glazing beads and upvc extruded interlocks, epdm gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), g.i. fastners 100 x8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. profile of frame & sash shyall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc.after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing.(single / double glass panes, wire mesh and silicon sealent shall be paid separately) - two track two panels sliding window made of (bigl series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 + or - 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(area of window upto 1.75 sqm upto 2.50 sqm) - sliding window size 1.50x1.35 m steel work welded in built up sections / framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets,gates and similar works cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc .complete - 40mm thick with 20mm nominal size stone aggregate providing and fixing commercial quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer) , of approved make (jhonson / asian / somany / nitco) in all colours, shades of size 200 x 300 mm as approved in skirting , risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 200x300 mm providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to is : 15622, of approved make (nitco / kajaria) in colours such as white, ivory, grey, fume red brown ,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including pointing the joints with white cement and matching pigment etc., complete providing and laying rectified ceramic rustic / matt finish floor tiles of size 600x600 mm or more (thickness to be specified by the manufacturer) of commercial quality conforming to is:15622 of approved make (somany / nitco) in all colours shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete painting top of roofs with bitumen of approved quality @ 17kg per 10 sq.m impregnated with a coat of coarse sand at 60cudm per 10 sq.m including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete - with residual type petroleum bitumen of grade vg-10 providing and laying pressed clay tiles (as per approved pattern 18mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2 integral water proofing compound , laid over a bed of 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete lime concrete terracing on roofs of required thickness laid to fall with 25mm nominal size brick aggregate and 50 lime mortar 1:2 (1 lime putty : 2 surkhi) rammed and finished with gur and belgiri treatment complete including rounding of junctions with parapet wall complete providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is: 13592 type a, including jointing with seal ring conforming to is: 5382, leaving 10mm gap for thermal expansion, (i) single socketed pipes - 110 mm diameter providing and fixing on wall face unplasticised - pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592 type a, including jointing with seal ring conforming to is: 5382, leaving 10mm gap for thermal expansion - single tee without door -110x110x110mm providing and fixing on wall face unplasticised - pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592 type a, including jointing with seal ring conforming to is: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe providing and fixing unplasticised - pvc pipe clips of approved design to unplasticised- pvc rain water pipes by means of 50x50x50mm hard wood plugs, screwed with m.s. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 110mm 15mm cement plaster on the rough side of single or half brick wall of mix - 1:4 (1cement : 4 fine sand) 12mm cement plaster of mix -1:4 ( 1 cement : 4 fine sand) 15 mm cement plaster on rough side of single or halfbrick wall finished with a floating coat of neat cement of mix - 1:4 (1 cement : 4 fine sand) finishing walls with textured exterior paint of required shade - new work (two or more coats applied @ 3.28 ltr / 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq.metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead - with cement mortar 1:4 (1 cement : 4 fine sand) white washing with lime to give an even shade - old work (two or more coats) removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scrarches etc.complete finishing walls with textured exterior paint of required shade - old work (two or more coats on existing cement paint surface applied at 3.28 ltr / 10 sqm demolishing lime concrete manually / by mechanical means and disposal of material within 50 metres demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead - of area 3 sqm and below dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead - for thickness of tiles 10mm to 25mm supplying fixing and commisioning of suguna/ texmo / sharp 1 hp monoblock pumpset slow speed single phase motor. the rate include the cost of pumpset , pumpset fixing in position and test run etc.complete providing and fixing white vitreous china pedestal type water closet (european type w.c.pan) with seat and lid, 10 litre low level white p.v.c. flusing cistern, including flush pipe, with manually controlled device (handle lever), conforming to is: 7231,with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required - w.c. pan with isi marked black solid plastic seat and lid providing and fixing wash basin with c.i. brackets, 15mm c.p. brass pillar taps,32 mm c.p.brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required - white vitreous china wash basin size 630x450 mm with a pair of 15 mm c.p.brass pillar taps providing and fixing p.v.c.low level flushing cistern with manually controlled device (handle lever) conforming to is:7231, with all fittings and fixtures complete - 10 litre capacity -white providing and fixing p.v.c. waste pipe for sink or wash basin including pvc waste fittings complete - flexiple pipe - 40mm dia providing and fixing astm pipes including all astm plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . this includes jointing of pipes & fitting with one step astm solvent cement and testing of joints complete (internal work exposed on wall ) - 20mm nominal outer dia pipes providing and fixing astm pipes including all astm plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . this includes jointing of pipes & fitting with one step astm solvent cement and testing of joints complete (internal work exposed on wall ) - 32mm nominal outer dia pipes providing and fixing ball valve (brass) of approved quality, high or low pressure, with plastic floats complete - 20mm nominal bore providing and fixing ball valve (brass) of approved quality, high or low pressure, with plastic floats complete - 25mm nominal bore providing and placing on terrace (at all floor levels) polyethylene water storage tank isi: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank - circular tank providing and fixing c.p.brass bib cock of approved quality conforming to is: 8931 - 15 mm nominal bore providing and fixing c.p. brass long nose bib cock of approved quality conforming to is standards and weighing not less than 810 gms - 15mm nominal bore providing and fixing c.p.brass angle valve for basin mixer and geyser points of approved quality conforming to is: 8931- 15 mm nominal bore making soak pit 2.5 m diameter 3 m deep with 45 x 45 cm dry brick honeycomb shaft with bricks of class designation 75 and 110mm dia upvc pipe (type b) 1.8 m long complete as per stadard design with f.p.s.bricks providing and fixing on wall face / column face unplasticised - pvc moulded fittings / accessories for unplasticisd - pvc soil and waste pipes conforming to is:14735 - 1999 including jointing with seal ring conforming to is :5382 leaving 10mm gap for thermal expansion - single tee without door - 110 x110x110mm supply of quarry rubbish including stacking to department gauge for premeasurement and spreading required thickness providing, laying and jointing upvc pipes(finolex / jain / supreme / truebore / nandi) (0.6 mpa)conforming to is specification 4985 and isi marked including transportation to the site, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement, excluding upvc specials such as bends, tees, threaded pieces, couplers, reducer, endcaps etc.,complete all as per is and cpwd specification. - 110mm dia.
